The preview

ControlClick or dragWith a modifier
Effect in the rowClick to place it under the first letter at 60. Drag it next to the words to place it there.Option-click (Alt-click on Windows) places it alone.
Placed effectDrag to move it. Click to play the animation again. Double-click, or drag it below the dotted line, to take it off.Shift-drag moves it finely.
In and OutClick to edit that end. Click the end you’re editing to play In then Out. Double-click to switch that end off. Click a switched-off end to switch it back on, linked.
Link between themClick to unlink In and Out, or to link them again with the edited end’s settings. Hidden while one end is off.
DiceRolls a new mix for the end you’re editing, or both when linked.Shift-click keeps the effects and rolls a new variation.
ClearSends every effect of the end you’re editing back to the row.
PresetsOpens the presets.

The bar

ControlClick or dragWith a modifier
Letters, words or linesClick to cycle Letter by letter, Word by word and Line by line.
DurationDrag up or down, click its arrows, or double-click to type. 1 to 600 frames.
OverlapDrag sideways, one percent a pixel, or double-click to type. 0 to 100%.Enter keeps a typed value, Escape cancels it.
ApplyApplies every end that’s on to the selected text layers.Cmd-click (Ctrl-click on Windows) removes Typhoon. Right-click for Remove Typhoon.
RemoveRemoves Typhoon from the selected text layers.

What the panel shows

  • The words are the first selected text layer’s, read when the pointer moves onto the panel, on one row and cut short if they’re long. With no text layer selected, they read Motion Fun.
  • A ribbon runs from each placed effect to the letter it starts from, in the effect’s color.
  • A ring in place of a dot is an effect sitting on the words.
  • The readout at the top names the effect being dragged, its strength, side and start, or the overlap being dragged and how long each letter takes.
  • The underline under In or Out marks an end that’s on, and fills while the preview plays it.

The preview plays at 30 frames a second, so its timing matches a 30 fps comp.

Messages

WhereMessageMeaning
MessageTyphoon in and out on 2 text layersIt worked. It names the ends it wrote.
Message· skipped 1 layer not text, 1 lockedSome selected layers were left alone.
MessageRemoved Typhoon from 2 text layersRemove worked.
MessageSelect text layers to animateNothing selected, or nothing selected is text.
MessageSelect text layers to clearThe same, for Remove.
MessageThe selected text layers are lockedEvery selected text layer is locked.
MessageNo active compositionNo comp is active.
MessageNo Typhoon on the selection to removeThe selected text layers have no Typhoon.
MessageNo Typhoon on the selection to pick upFrom selected layer found no Typhoon.
MessageExpression error: and the errorAfter Effects couldn’t run the animation. Nothing is left on the layer.
Apply or RemoveNo selection, No text, Locked, No comp, Nothing or Not doneThat click was refused, for the reason in the message beside it.
Apply or RemoveA count, such as 2 layersHow many layers it changed.

Slot sizes

Typhoon’s default slot is three quarters of the dock wide and 14 rows tall. Its smallest slots are 4 columns by 5 rows, 7 columns by 3 rows, or the full width by 2 rows.

In a narrower slot, the bar takes two rows. The duration and overlap sit on the first, and letters, Apply and Remove on the second. When the preview is too narrow for its corners, the dice, clear and presets move into the bar too.

In a slot too small for the preview, Typhoon becomes eight tiles. They are In, Out, dice, clear, presets, letters, a sliders tile and Apply. The sliders tile opens the duration, the overlap, Link In and Out and Remove.

There are no effects to drag here. Use the dice and the presets, or make the slot bigger.